How to Fix a Washing Machine Not Draining Water and Spinning

If you have a washing machine that is not draining water and spinning, you need to investigate the reason for this problem. There are several things you can do to fix this problem, including checking the drain hose and pipe. In addition, you should also check for clogs in the drain.

What causes washing machine not to drain and spin?

If your washing machine won’t drain and spin, there are a few possible causes. One of the most common is a broken lid switch. These switches prevent your machine from spinning with the lid open. Unfortunately, the lid switch is a delicate piece of equipment and can easily break. Many people use the front loading door to slam it shut, leaving it open, or leave the top loading lid dangling. This causes water to back up in the machine.

Another cause of a washing machine not draining and spinning is a blocked drain hose. This prevents water from draining properly and stops the spinning cycle. Sometimes lint, hair ties, and other small objects can clog up the drain hose, causing the machine to drain slowly or not at all.

Another reason a washing machine won’t drain is a defective lid switch or door lock. These can be replaced with a multimeter. Otherwise, you can call a repairman to fix the problem.

4 Reasons Your Washing Machine Won’t Drain or Spin

If your washing machine won’t drain or spin, you need to find out why. There are several possible reasons for this problem. One of the most common is that the drain hose has become clogged. To check for clogs, remove the hose and inspect it. If it’s clogged, you may need to use a bucket and towel to clean the pipe.

Another reason for your washing machine not to drain or spin is that the pump is clogged. If you can’t see the drain hose or pump, the pump filter may be clogged. It’s best to clean the filter every three months or whenever it becomes clogged. The pump filter is located at the bottom right-hand corner of your washing machine.

Checking the pump is an easy task that may involve unscrewing two screws at the bottom of the machine. Unscrewing two screws will open the access panel. Once you’ve accessed it, you should check the fan blades and arms, and the outlet part. You may need to replace the pump altogether.

Troubleshoot top-load washer won’t drain or spin

When a top-load washer won’t drain or begin spinning, you may need to find the cause of the problem. In some cases, a broken pump, a clog in the drain pipes, or a damaged part can block the water from flowing out. In any of these cases, you’ll need to replace the parts.

First, check the drain hose. If you can see a clog in the hose, you can remove the blockage and drain the washer. If you can’t drain the water, you may have to call a plumber to fix the issue.

If the problem persists, you can try cleaning the coin trap. These traps usually have an easy-to-access panel. If cleaning the coin trap doesn’t fix the problem, you can check the water level valve. In some cases, the valve may be corroded.

Check the top-load washer drain pump

The first step to troubleshooting a not-draining washing machine is to check the pump for clogs. The pump must be able to drain the water properly and a clog will prevent the washing machine from draining. You can check this by lowering the drain hose into a bucket and checking for any obstructions. If the pump is not functioning properly, you should contact a plumber or an appliance store.

If you have difficulty accessing the pump, you should first unplug your washing machine from the wall and remove the drain hose. Next, look at the drain pump’s filter. This filter is located either on the front or behind the washing machine. To access the pump, remove the access panel and hose. If you find clogs, you should replace it.

You can also check the drain pump using an ohmmeter. The pump should read between five and ten ohms. If the reading is less than five ohms, then you need to replace the pump. Another possible cause of your washing machine not draining water is a worn or damaged drive belt. The drive belt is the mechanism that moves the pump, and it should be checked for broken plastic parts or restricted moving parts.

How do you clean a top load washing machine filter?

One of the most frustrating problems you can have with a washing machine is a clogged filter. This prevents the water from draining correctly and causes your clothes to drip. To fix this problem, clean the filter. You can easily do this yourself by using a damp cloth.

In the first step, mix a cleaning solution with some water. This mixture will remove trapped residue and clogs. Next, rinse out the filter. You can also use a soft bristle brush to scrub the filter. After cleaning the filter, replace the access panel.

The filter access door is located on the right side of your washing machine. Some models have a push release mechanism, but other models require a flathead screwdriver to unscrew it. Behind the access door, you’ll find a round dial and a rubber hose that is held in place by a clip.

Check the washing machine timer

To troubleshoot a washing machine that won’t drain water, start by checking the timer. The timer controls all the functions of the washing machine. It will contain a series of electrical contacts, some of which will control the timer’s motor and others will control the washing machine’s lid switch. If the timer doesn’t advance when you try to start the washing cycle, the water removal system may be blocked or damaged, and the machine will continue to run and not drain the water.

The door latch is another common issue that prevents the washing machine from moving forward. When you close the door of the washing machine, the door latch activates an interlock that prevents the door from opening while the machine is running. A faulty door interlock can be difficult to diagnose and repair, and is best left to a qualified repairman. You may also notice a weird noise coming from the washing machine, which may indicate a problem with the drain pump.

A problem with the drain pump may be caused by a foreign object lodged in the pump. Another possible cause of a washing machine not draining water is a worn belt. Check the belts for any signs of damage or wear, as damaged ones may break.

Test the washing machine lid switch

If your washing machine is not draining water, you may have a faulty lid switch. This small plastic switch is located under the lid or door of the machine. When pressed, it should make a click sound. If it doesn’t, you may have a broken lid switch, which requires replacement. Another possible cause is a worn or damaged belt.

If you can’t drain water from your washing machine despite attempting to close the lid, you might need to replace the lid switch. The lid switch is a safety mechanism that prevents the motor from receiving power from the water inlet valve. If it’s broken or malfunctioning, the washing machine won’t operate. Most lid switches are located in the top right corner of the machine.

In order to test the lid switch, remove a small load from your washing machine and try running it. Make sure the lid switch is not sagging or cracked; it should be flush with the top panel of the machine. Also, make sure to unplug the washing machine before servicing it.

See below for the list of cities we service within the Atlanta Service Area and Other Communities in Fulton County GA

Atlanta, Sandy Springs, Roswell, Milton, Johns Creek, Dunwoody, Brookhaven, Alpharetta


Tap to CALL